How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
The author is making a few great pointers on Tools You Need to Install a New Bathtub in general in this great article beneath.
Setting up a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably difficult project. If the old tub is easily obtainable, the task can move quickly; if you have to open a wall surface to eliminate the old bathtub and also place the brand-new bathtub, the task is much harder. In either case, the job is within a house handyman's skills, although you will certainly require an assistant to leave the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you might require a specialist plumber to make tube links.
This write-up will certainly aid you set up a brand-new tub in your restroom if you have already bought a brand-new bathtub and also do not need to alter the arrangement of your previous water supply pipes.
Your devices and also product list ought to comprise the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, switch on the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Before going on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap as well as the sink. Secure the tap in position with the producer supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Making use of the two wooden boards under its feet, put the bath tub in the required setting. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub up until the level reviews level.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the water supply and inspect all joints as well as brand-new pipework for leakages as well as tighten them if essential. Load the bath tub as well as also check the overflow outlet and the normal outlet for leaks.
Lastly, repair the bath paneling as explained in the maker's user's manual. Tiling as well as securing around the tub must wait up until the tub has actually been utilized a minimum of once as this will settle it into its final position.
Preparing for the Installation
Firstly, the supporting structure provided with the bathroom must be fitted (if called for) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to prevent strain on the bath tub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealant can break rather early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the market. It is a good idea to fit the tiles using waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that report about A Step-by-Step Guide to Installing a Bathtub through a friend on a different site. Are you aware of another individual who is occupied with Tools You Need to Install a New Bathtub ? Be sure promote it. I am grateful for your time. Visit again soon.
Book A Free Estimate Report this page